朝凯煤矿露天台阶爆破装药结构优化应用研究

本文以神达朝凯煤矿正在开采的台阶为工程背景,针对该矿在台阶爆破过程中存在着大块率高、根底多的现象,通过改变装药结构的方式对爆破参数进行优化。实践证明,优化后大块率和根底问题的治理效果明显。     

Inhibition of stress corrosion cracking in 304 stainless steel through titanium ion implantation

The effects of titanium ion implantation on the stress corrosion cracking (SCC) behaviour of 304 austenitic stainless steel were studied. Slow strain rate tests (SSRTs) were conducted on 304 steel in air and in 5?wt-% NaCl solution. The microscopic effects of ion implantation were evaluated by Stopping and Range of Ions in Matter Procedures (SRIM). Fracture morphologies and microstructures were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The fracture surfaces illustrate that ion implantation significantly inhibits the corrosion pits that initiate SCC. A dense passive film, which inhibits SCC, was formed during the ion implantation process. SCC initiation was restrained due to the dense dislocation nets that were generated by titanium ion implantation.

Highlights

• Ion implantation inhibits SCC susceptibility.

• The lack of Cr at the grain boundary leads to the expansion of SCC along the grain boundary.

• Implantation-induced damage leads to high-density dislocations.

• The surface was amorphised due to high-density dislocations.

     

宁夏红寺堡盆地隐伏古隆起成因机制及其对区域沙漠化的影响

目前对于青藏高原东北缘活动构造研究多集中于活动断裂带的活动性,而对夹持于其间的沉积盆地构造格架及活动性研究甚少。以夹持于烟筒山断裂与牛首山—罗山断裂之间的宁夏红寺堡盆地为研究对象,采用重力资料重处理解译、音频大地电磁测深(AMT)和地震勘探相结合,揭示红寺堡盆地隐伏构造特征,并进一步采用盆山一体化思路分析隐伏构造的成因机制及其对区域沙漠化的控制作用。结果表明:青藏高原在中新世末发生强烈的NE向推挤、扩展和隆升,红寺堡盆地由坳陷盆地转变为挠曲盆地; 在青藏高原NE向扩展的影响下,烟筒山断裂发生强烈的逆冲作用,古生代—中生代基底逆冲于古近系—新近系之上,受构造变形影响的最新地层为中新统彰恩堡组; 红寺堡盆地内的隐伏古隆起呈NW—SE向,与烟筒山构造带具有相同的构造动力学背景,受青藏高原NE向扩展影响形成于中新世末,并且至今仍具有活动性; 隐伏古隆起周缘断裂的活动破坏了地表稳定性、蓄水能力和地表植被,导致区域沙漠化呈现有规律的NW—SE向带状展布。该研究成果对于宁夏红寺堡盆地区域稳定性评价及沙漠化的综合治理具有现实指导意义。     

Cutting parameter optimization for one-step shaft excavation technique based on parallel cutting method

The outcome of the cutting blasting in a one-step shaft excavation is heavily related to the cutting parameters used for parallel cutting method. In this study, the relationships between the cutting parameters (such as the hole spacing L and the empty hole diameter D) and damage zones were investigated by numerical simulation. A damage state index γ was introduced and used to characterize the crushing and crack damage zones through a user-defined subroutine. Two indices, i.e., η₁ and η₂ that can reflect the cutting performance, were also introduced. The simulation results indicate that an optimal value of L can be obtained so that the η₁ and η₂ can reach their optimal states for the best cutting performance. A larger D results in better cutting performance when the L value maintains its best. In addition, the influences of the loading rate and the in-situ stress on the cutting performance were investigated. It is found that an explosive with a high loading rate is suit for cutting blasting. The propagation direction and the length of the tensile cracks are affected by the direction and the magnitude of the maximum principal stress.     

再加工工艺对N18锆合金板残余应力的影响

采用“热轧+冷轧+退火”工艺对N18锆合金板进行再加工,通过X射线法分析板的表面残余应力,采用EBSD技术分析晶界取向差角分布和大小角度晶界。结果表明,热轧后N18锆合金板的表面残余应力呈现无规律分布状态;冷轧后板的表面残余应力均为压应力,其大小随着冷轧变形量的增加而增加;退火后板的表面残余应力值处于较低水平,当退火制度为500 ℃×2 h时,残余应力处于最低水平;退火后,板的微观结构以小角度晶界为主,且随着退火温度的升高,小角度晶界的密度先增加后趋于稳定。     

Effect of cutting process on the stress corrosion susceptibility of AISI 304L stainless steel

During manufacturing of a component, cutting, turning, grinding, and milling operations are inevitable and these operations induce surface residual stresses. In this study, it is shown that, depending on the process employed for cutting, residual stresses generated at the cut surfaces can vary widely and they can, in turn, make the cut surfaces of austenitic stainless steel (SS) prone to stress corrosion cracking (SCC). An austenitic SS 304L plate was cut using three different procesess: bandsaw cutting, cutting using the cut-off wheel, and shearing. Surface residual stress measurement using the X-ray diffraction (XRD) technique is carried out close to the cutting edges and on the cross-section. SCC susceptibility studies were carried out as per ASTM G36 in 45% boiling magnesium chloride solution. Optical microscopic examination showed the presence of cracks, and confocal microscopy was used to measure the depth of cracks. The study confirmed that high tensile residual stresses present in the cut surfaces produced by cut-off wheel and shear cutting make the surfaces susceptible to SCC while the surfaces produced by bandsaw cutting are resistant to SCC. Hence, it is shown that there is a definite risk of SCC for product forms of austenitic SS with cut surfaces produced using cutting processes that generate high tensile residual stresses stored for a long period of time in a susceptible environment.     

Stability analysis and characterization of the nano emulsified Jatropha-curcas-based bio-fuel

This work investigates the suspension duration of the nanosized multiwalled carbon nanotubes (MWCNT) and aluminum oxide (Al₂O₃) in B20, B50 and B70 blends of Jatropha Methyl ester. The MWCNT and aluminum oxide (Al₂O₃) are added to the fuel blends in the proportions of 50 and 100 pmm separately by ultra sonication. The prepared fuel samples are characterized, and turbidity analysis was done to find the stability rate of nano-additives. The outcomes reveal the maximum stability rate for MWCNT and Al₂O₃ as 83.3% and 87.03%, respectively, with 50ppm in B20 over a period of eighteen days. A considerable drop in suspension was observed with the 100 ppm MWCNT and Al₂O₃ biodiesel blends.     

微结构模芯的精密磨削及其在微注塑成形中应用

针对微结构聚合物元器件的批量化生产与制造效率低等问题，采用精密修整成V形尖端的金刚石砂轮，在自润滑性和脱模性良好的钛硅碳陶瓷模芯表面加工制造出形状精度可控的V沟槽阵列结构，然后利用微注塑成形工艺将模芯表面的V沟槽阵列结构一次成形复制到聚合物表面，高效注塑成形制造出倒V形阵列结构的聚合物工件。分析了微模芯的表面加工质量与形状精度，研究了熔体温度、注射速度、保压压力、保压时间等微注塑成形工艺参数对微结构聚合物注塑成形角度偏差和填充率的影响。实验结果表明：通过微细磨削加工技术和微注塑成形工艺可以高效率、高精度地制造出规则整齐的微结构注塑工件，注射速度对微成形角度偏差的影响最大，保压压力对微成形填充率的影响最大，微结构模芯的微细磨削形状精度值为4.05 μm，微成形的最小角度偏差和最大填充率分别为1.47°和99.30%。     

松河井田多煤层资源开发条件及合采储层伤害特征

为了降低煤层气井排采过程中的储层伤害,通过分析松河井田的资源开发条件及煤层气井排采数据,总结各排采阶段不合理排采控制引起的储层伤害特征,提出不同排采阶段合理的排采工艺对策。分析结果表明:松河井田煤层气资源丰度达到2.09×10^8m^3/km^2,煤层气资源开发条件较好;松河井田多煤层合层排采过程中,不合理排采控制工艺对煤层气井的产气量影响较大;排采初期以速敏伤害为主,排采中期以气锁和应力闭合伤害为主;修井作业及停抽期间,气锁效应及应力闭合对煤层造成伤害的可能性增大。合理的排采控制能够有效降低煤层气井的储层伤害,提高煤层气井产气量。     

旋转式采煤工艺在煤矿生产中的应用

采煤工艺作为煤矿正常生产的核心,直接关系到综采作业的效率、煤炭回采率和综采作业的安全性,随着对综采作业要求的不断提高,旋转式采煤工艺在煤矿井下的应用范围也不断扩大。以黄家沟煤业1205综采作业面为分析对象,对旋转式采煤工艺在井下的应用情况进行了研究,为优化综采方法、提升综采作业效率和煤炭回采率奠定基础。